Niki.Tasha – Lesson 11 – Sides and Bottom

Hiya, Niki.   This lesson brings your personal sense of style into this peyote tube amulet bag.  You have finished with the graph for a short time.  Don’t get rid of it:  it has your notes about the pattern on it.  Just tuck it away in a safe place where you can easily find it again.  Right now it’s time to simply look at the tube you have created. 

In photography and the different software packages you can ‘crop’ an image by moving the borders in and out.  You can manipulate the size of the photo and you can focus on just a section of the picture, too.  That’s what we are doing now but in our hands, not on the computer.

Gently squeeze the tube to see what one side might look like.  Then make the tube round again and squeeze it in a different place.  What you are looking for is the most attractive design, in your opinion.  At this stage , you don’t have to stick to the design as graphed.  Perhaps you like the design to wrap around the side of the amulet bag.  You might like the side to cut the image by 3/4’s:  3/4s of the image on one side, and only 1/4 of the image on the other side.

Flip the tube upside down:  you may prefer the design that way.  

Keep in mind that you will be making the bottom of the amulet bag, a flap, a strap, and fringe, too. 

Keep in mind, also, that there are 2 bottoms and 3 tops you can apply to your design.  This Step 11, will give you one alternative bottom. 

Youhave chosen the part of the design that will show on the front and back.  Gently squeeze the tube flat, paying attention to 1 detail.  The teeth that were formed when you started this tubular peyote glass bead amulet bag need to be lined up at the bottom like teeth of a zipper.  ZigZag. 

With the long tail kept at the very beginning of this project, remove the stop bead, and thread your needle.  The working thread needs to be at 1 side, decided by you when you were tube squeezing.  Run the needle through the next ‘tooth’, pick up a bead, run the working thread through the next ‘tooth.’  Continue in this fashion until you reach to other side. Run through the last ‘tooth’, pick up a bead and put the needle through the first ‘tooth’ of the next row.  Return to my diagrams of starting Peyote Technique My Way.  Go back and forth for a couple of rows. 

Now,run your needle through the teeth alternating from side to side.  After every 3 or so ‘teeth,’ pull up the thread and the zipper will begin to close.  It is easier to obtain a nicely closed zipper if you pull up your thread firmly every 2 – 3 zigs. 

When the zipper is closed, neatly tie off the thread by running it back and forth through nearby beads.

peyote-even-flat

Without doing another thing to this item of glass bead  artisan jewelry, you can tell people you have completed an amulet bag. 

Pick a bead or charm that represents you.  In our First Nations each family and person has a totem.  A person may be of the bear clan and that person is a water bear:  s/he might add a bear paw charm to his/her amulet bag.  This token is a ‘totem’ by which s/he can be identified and it brings him/her good luck.

Thissame idea can be used by all races and religions:  Christians might wear a cross or crucifix, Jews may wear a Star of David, the Star and Crescent belong to Muslims, a Kirpan for the Sikhs.  Individuals may identify strongly with  something in the animal world:  dragons, bears, parrots for example, and that would be their personal totem.  A charm indicating this personal totem might be slipped into an amulet bag.  Have you such a totem, Niki?

If you add lucky charms to your amulet bag it is a good idea to tie them in:  use a piece of thread knotted and tucked inside, or run a thread of beads through the charms and loop it neatly inside to secure your totem.

You can also finish the bottom with a round flat piece of peyote and for that technique see the next lesson.

Copyright © 2008 Helene Turnbull All rights reserved.  No part of this work covered by the copyrights hereon may be reproduced or used in any form or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping or information storage and retrieval systems – without written permission of the author.

Advertisements

Niki.Tasha – Lesson 8 – Peyote Stitch My Way

Hiya, Niki;  here is my alternative Tubular Peyote Technique.  You will note that much of my method is the same as the traditional technique written out in Lesson 7.  I know a picture is worth a thousand words and I will add pictures once I figure out my new designing software.  I promise. 

These instructions relate to the designs offered in Lesson 5.  So, let’s begin.

1. Cut a length of thread 2 yards long.  Thread your needle and pull both needle and thread through the Thread Heaven® or beeswax a couple of times.  Then, stretch the thread as you run the needle and thread through one hand several times.  The friction creates heat and that helps settle the beeswax or Thread Heaven deep into the thread.

2. Put 1 bead on the thread and pull it through, leaving a tail of about 12 inches from the end.  Run the needle through the bead a 2nd time.  Be sure not to pierce the thread already run through the bead.  This is the ‘stop bead’ which will help keep all your beads on the thread and it should be able to move easily along the thread.

3. String 84 beads on the thread.   Check and double check your count.  This design is an even number peyote technique and these 84 beads make the first 2 rows. 

4. If you are right handed, Niki, you will be working from right to left.  But, if you are a leftie like me, your needle and ‘working thread’ will move from left to right.  …  Add a bead on your ‘working thread’:  the thread coming OUT of a bead and THROUGH the eye of the needle, and run your needle through the next bead, the 2nd bead from the end that’s not got the stop bead on it.   Add another  bead on your needle, skip a bead and run the needle through the next bead.  Continue in this way, adding a bead and running your working thread through every 2nd bead, until you return to the stop bead.   Do not include the stop bead in any of your patterns:  its a bead working independently of the design.  Carefully smooth out the beads and make a knot:  I prefer a surgeon’s knot and the version I found at Florida Sportsman is, by far, the best way of making this knot that I have ever seen.  Be sure the stop bead remains free from the circle of beads.  The knot you use is up to you as long as it doesn’t pull free and is not bulky.  Do you know the square or reef knot or the surgeon’s knot?

Square or Reef Knot:  http://en.wikipedia.org/wiki/Square_knot

Surgeon’s Knot:  http://en.wikipedia.org/wiki/Surgeon%27s_knot  or http://www.floridasportsman.com/HowTo/knots/surgeons_knot/  I prefer this version for its simplicity.

Niki, you may now remove the stop bead if you wish:  I prefer to keep it because it will indicate the beginning and ending of the original row.  That helps when working your pattern.  It also acts as a weight on that 12 inches of tail thread which helps keep it out of the way of your working thread.  Please don’t cut off the tail:  you will be using it later.

5.  You have now completed the 3 foundation rows.  You recognize that the Peyote technique is a diagonal stitch pattern:  the beads take on a zipper appearance with one bead up and one bead down.  On all future rows the beads you add, one at a time, will fill in the spaces between each ‘up’ bead.  At the end of each row in the Tubular Even Count Peyote Stitch Technique the needle will go through the last bead of the row AND the 1st bead of the next row:  this positions your working thread to begin filling in the blanks of the next row.

NOTE:  Following either of the 2 patterns offered in Lesson 5, only 1 portion of the design has been graphed.  It is up to you whether or not you repeat the design on the backside.  Your stress level will be lower if you work the back in one solid colour.  Once you get the hang of things, you can add a 2nd full design on the backside or mix things up any way you like.

Ending and Beginning a Working Thread:

6.  Don’t work your design until you have run out of thread.  Allow at least 4 inches of working thread to use in ending the thread.  Run your needle through beads, one at a time, in a downward diagonal line.  Every 3 beads run the needle through the bead immediately above the bead your needle has just exited.  One at a time again, run the needle through another 2 or 3 beads.  Double back as before until a) you run out of working thread, or b) you are satisfied that the thread will not work its way loose. 

NOTE:  Some beaders add a discreet overhand knot or 2 during their finishing a thread.  A small dab of glue … is added by some beaders with steady hands.  I have had great success with my method without the knots and the glue (my hands shake too much).

7.  Your 2nd and all other threads need not be nearly as long as the first one.  I like to use a thread 3 1/2 ft in length.  Leaving a tail of about 3 inches long, run the needle through your beads in an upward diagonal manner exactly the way you did to finish a thread.  You will double back several times and check to ensure the thread is not going to work its way free … tug on the working thread.  Bring your needle up in the exact same spot on the row as where you stopped adding beads.

8.  Continue working until you run out of pattern.  The last row must be even all around – don’t end in the middle of the row.  If you have lots of thread left in your needle, don’t cut the thread off. 

9.  The designs I listed in Lesson 5 have no colour notations.  It is your choice what colours to use.  As mentioned, if you add your favourite colour as the basic, you will enjoy the process a whole lot more.  Keep a balance of bright shiny beads and flat matte beads.  The play of light on the different bead finishes adds to the design.  Remember, a little goes a long way. 

I hope you enjoy your first project, Niki.

GLOSSARY: 

Tubular Peyote Stitch:  A technique in which a hollow tube is created by adding a bead in the space between 2 beads of the previous round.

Stop Bead:  A bead through which the needle passes twice  to keep all the beads on the thread.  After the first 3 rows it acts as a weight to help identify  and keep the long tail away from the working thread.

Working Thread:  The thread going from a bead and through the eye of the needle.  It becomes evident once some beads are added.  ‘Working Thread’ becomes a helpful shorter term when describing a complicated needle movement.

Copyright © 2008 Helene Turnbull.  All rights reserved.  No part of this work covered by the copyrights hereon may be reproducted or used in any form or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems – without written permission of the author.

Niki.Tasha – Lesson 7 – Peyote Stitch

Peyote Lesson 7 - Art Deco Design

Peyote Lesson 7 - Art Deco Design

There are many good books that can give you the instructions of the Peyote Stitch.  My favourite is a small, spiral bound book by Judith Durant & Jean Campbell:  ‘The Beader’sCompanion” , printed by Interweave Press, Inc. ISBN 1-883010-56-X.  Here is a link to Amazon.com where you can pick up this great little book and at a reasonable cost to yourself.  http://www.amazon.com/s/ref=nb_ss_gw?url=search-alias%3Daps&field-keywords=Beader%27s+Companion .  There is also the ‘New Beader’s Companion’ at this same site.

In this and the next lesson, Niki, I will give you 2 different ways to start the peyote stitch tube:  the generally accepted way and then my way.  You can try both and decide for yourself which you prefer; you may even make a 3rd method which would be the Niki.Tasha way.

1. Cut a length of thread 2 yards long.  Thread your needle and pull both needle and thread through the Thread Heaven® or beeswax a couple of times.  Then, stretch the thread as you run the needle and thread through one hand several times.  Believe me, this really helps cut down the kinks and knots as you are stitching.

2. Put 1 bead on the thread a tail of about 12 inches from the end and run the needle through the bead a 2nd time.  This is the ‘stop bead’ which will help keep all your beads on the thread.

3. String 84 beads on the thread.   Check and double check your count.  This tube is an even number peyote pattern and these 84 beads make the first 2 rows.  The beads must be held loosely on the thread.  The slack will be taken up in the next step.

NOTE:  You must ensure the beads have lots of room because they will shift as you add the next row.  Calculating how much space to give these beads comes with practice and I admit I have never been able to figure out just how much slack is needed.

4. Run your needle through the 1st two beads, from right to left, beside the stop bead to create a tube.  … If you are right handed, Niki, you will be working from right to left.  But, if you are a leftie like me, your needle and ‘working thread’ will move from left to right.  …  Add a bead on your needle, skip a bead on your tube and run your needle through the next bead.   Add another  bead on your needle and skip a bead, and run the needle through the next bead.  Continue in this way, adding a bead and running your working thread through every 2nd bead, until you return to the beginning.   Slip your needle through the first 2 beads of the row just finished. 

Niki, you may now remove the stop bead if you wish:  I prefer to keep it because it will indicate the beginning and ending of the original row.  That helps when working your pattern.  It also acts as a weight on that 12 inches of tail thread which helps keep it out of the way of your working thread.

5.  You have now recognized that the Peyote technique is an offset pattern.  Following either of the 2 patterns offered on the last post, only 1 portion of the design has been graphed.  It is up to you whether or not you repeat the design on the backside.  Your stress level will be lower if you work the back in one solid colour.  Once you get the hang of things, you can add a 2nd full design on the backside or mix things up any way you like.

Ending and Beginning a Working Thread:

6.  Don’t work your design until you have run out of thread.  Allow at least 4 inches of working thread to use in ending the thread.  Run your needle through beads, one at a time, in a downward diagonal line.  Every 3 beads run the needle through the bead immediately above the bead your needle has just exited.  One at a time again, run the needle through another 2 or 3 beads.  Double back as before until a) you run out of working thread, or b) you are satisfied that the thread will not work its way loose. 

NOTE:  Some beaders add a discreet knot or 2 during their finishing a thread.  A small dab of glue is added by some beaderswith steady hands.  I have had great success with my method without the knots and the glue (my hands shake too much).

7.  Your 2nd and all other threads need not be nearly as long as the first one.  I like to use a thread 3 ft in length.  Leaving a tail of about 3 inches long, run the needle through your beads in an upward diagonal manner exactly the way you did to finish a thread.  You will double back several times and check to ensure the thread is not going to work its way free … tug on the working thread.  Bring your needle up in the exact same spot as where you ended.

8.  Continue working until you run out of pattern.  The last row must be even all around – don’t end in the middle of the row.  If you have lots of thread left in your needle, don’t end and cut the thread off.  Jump to Lesson 8 – Bottom’s Up.

6.  The designs I listed in Lesson 6 have no colour notations.  It is your choice what colours to use.  As mentioned, if you add your favourite colour as the basic, you will enjoy the process a whole lot more.  Keep a balance of bright shiny beads and flat matte beads.  The play of light on the different bead finishes adds to the design.  But, a little goes a long way. 

I hope you enjoy your first project, Niki.

GLOSSARY: 

Tubular Peyote Stitch:  A technique in which a hollow tube is created by adding a bead in the space between 2 beads of the previous round.

Stop Bead:  A bead through which the needle passes twice  to keep all the beads on the thread.  After the first 3 rows it acts as a weight to help identify  and keep the long tail away from the working thread.

Working Thread:  The thread going from a bead and through the eye of the needle.  It becomes evident once some beads are added.  ‘Working Thread’ becomes a helpful shorter term when describing complicated needle movement.

Copyright © 2008 Helene Turnbull.  All rights reserved.  No part of this work covered by the copyrights hereon may be reproducted or used in any form or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems – without written permission of the author.